Eliminate loud humming noises and restore a smooth ride with A-Premium Wheel Hub Bearings. Precision-engineered to strict OE standards for maximum safety.
SOLD
OUT
SOLD
OUTA hub bearing supports wheel rotation at a specific corner of the vehicle, and fitment depends on more than year and model. Enter the complete vehicle, then confirm front or rear position, driver or passenger side, drive type, wheel stud count, flange dimensions, ABS sensor configuration, and package quantity. Read every trim, drivetrain, and body-style note because a similar-looking wheel hub assembly may use different mounting or sensing features.
A wheel bearing may be serviced as a separate pressed component on some vehicles. A wheel bearing and hub assembly combines the bearing with a mounting hub and may also include wheel studs or an ABS-related component. A-Premium category products include preassembled hub units, but included parts vary by SKU. Confirm the item title, product images, specifications, and notes instead of assuming every wheel hub bearing includes the same hardware.
The required repair depends on the vehicle's wheel-end design and the condition of the surrounding parts. If the service procedure calls for a separate bearing, a complete assembly may not be an alternative. If it specifies a unitized hub, do not disassemble the sealed unit to reuse internal components.
Wheel hub assemblies can share a general shape while differing at the mounting flange, wheel face, axle, or sensor. Verify these configuration details together.
A humming, growling, or grinding sound that changes with road speed, noticeable wheel play, vibration, or an ABS warning can justify wheel-end inspection. These signs do not identify the hub bearing by themselves. Tire noise, brake contact, a CV joint, axle hardware, alignment issues, or a separate wheel-speed circuit fault may sound or behave similarly.
Inspect the tire, brake, hub, axle, knuckle, and wiring using the vehicle procedure. If an ABS code is present, test the circuit and inspect the related ABS speed sensor, connector, harness, and encoder or tone ring before choosing a hub. Replacing a bearing without isolating the fault can leave the warning or noise unchanged.
Compare the original assembly with the selected product before installation: flange pattern, pilot diameters, splines where applicable, stud count, connector, cable routing, and mounting position should agree. Keep the mounting surfaces clean and inspect the steering knuckle and axle threads for damage. Route any sensor lead through the original clips and away from rotating or hot parts.
Use the vehicle manufacturer's tightening sequence and torque specifications for the mounting bolts, axle nut, brake components, and wheel. Follow the specified tools; where the procedure calls for a calibrated torque wrench, do not substitute an impact wrench. After assembly, check free rotation, brake operation, sensor routing, and warning lights. Arrange an alignment check if the repair disturbed alignment-adjusting components or if tire wear and tracking symptoms remain.
Not always. Some vehicles use a separate press-in bearing, while others use a unitized bearing and hub assembly. Follow the product listing and the vehicle service design.
Not in every case. Replace the diagnosed side unless inspection, mileage, service guidance, or a paired product supports doing both. Confirm package quantity before ordering.
Some assemblies include an ABS sensor or encoder and others do not. Check the product specifications, connector details, images, and vehicle notes for the selected SKU.
No. Stud count, bolt circle, flange, pilot, and axle details must match the application. Use the vehicle selector and compare the original assembly before installation.
It depends on the repair procedure. If alignment-adjusting or suspension components were disturbed, or tracking and tire-wear symptoms remain, have alignment checked to vehicle specifications.
ABS light on after hub replacement? Diagnose loose connectors, damaged wiring, or incorrect parts. Read codes, inspect signals, and verify compatibility before buying new components.
This guide breaks down the physics behind the noise, provides a direct comparison of the symptoms, and delivers a step-by-step DIY diagnostic process to help you pinpoint the exact culprit before you start buying replacement parts.
C0031 indicates a left-front wheel speed sensor circuit fault, not necessarily a bad sensor. Diagnose wiring, connectors, rust, tone rings, or bearings before replacing parts to avoid unnecessary repairs and restore ABS safety systems.
A wheel bearing supports the vehicle’s weight and allows the wheel to rotate, while a hub assembly is a complete unit with the bearing already installed. This guide explains their differences, replacement methods, costs, and how to choose the correct part
By understanding how car hub bearings work, drivers can make informed decisions about repairs and replacements.
