Shop precise fit replacement Brake Caliper to maintain and improve your vehicle's performance. Find the right parts for your make and model, backed by excellent customer service at A-Premium.
A disc brake caliper uses hydraulic pressure to move its piston or pistons and clamp the pads against the rotor. For a brake caliper replacement, enter the full vehicle information and confirm front or rear, driver or passenger side, piston count, quantity, and bracket details. Braking parts that look alike may differ by trim, wheel or brake package, transmission, and production configuration.
Current A-Premium listings include single calipers, paired calipers, front-and-rear kits, and one-, two-, or four-piston configurations. Some products are a brake caliper with bracket, while others specifically exclude the bracket. Mounting bolts may be included or omitted independently, so verify each component on the product page.
A Driver Side Brake Caliper and Passenger Side Brake Caliper are side-specific. A front brake caliper should not be substituted for a rear brake caliper, even if the casting looks similar. Compare the removed assembly, hose connection, bleeder location, mounting points, piston count, and the listing's exact position before ordering.
Fluid around a caliper, a soft or low pedal, pulling, excessive heat, dragging, noise, or uneven pad wear warrants prompt inspection. These conditions do not identify the caliper by themselves. A restricted hose, worn pads or rotors, air in the hydraulic system, wheel-bearing play, or suspension and alignment problems can contribute to similar complaints.
Clean the suspected area and confirm whether the substance is brake fluid rather than assembly grease. On some replacement calipers, assembly grease near the piston boot can resemble leaked fluid, so clean the area and recheck it before diagnosing a hydraulic leak. Inspect the piston boot, bleeder, hose connection, and caliper body, and test the hydraulic system according to vehicle service information.
Inspect the brake pads and rotor friction surfaces for uneven wear, scoring, contamination, or heat damage. A dragging caliper can affect nearby parts, but replace each item according to measured condition and the service limits for that vehicle. Confirm that the new pads match the caliper and brake package.
Check the brake hydraulic hose for cracking, leakage, damaged fittings, twisting, or restriction. Then review the caliper listing for wheel size, submodel, brake option, transmission, piston material when stated, bracket inclusion, and mounting hardware. Product-page notes take priority over a broad year-and-model match. When more than one brake package is listed, compare the removed caliper, rotor arrangement, and vehicle option information before choosing.
Use the vehicle manufacturer's procedure for lifting, hose handling, fastener tightening, brake fluid, bleeding, parking-brake service, and any electronic service mode. After installation, verify a firm pedal before moving the vehicle, inspect every opened connection for leakage, and confirm that the wheel turns and the brakes apply and release correctly. Do not drive with an active fluid leak, a brake warning, or a soft pedal; arrange professional inspection if the system cannot be verified.
The caliper and mounting bracket are included when the listing says so, but bolts, clips, pads, hoses, and other hardware may not be. Check the exact product specifications.
Not in every case. Replace parts based on diagnosis and condition, while comparing operation and wear on both sides of the axle. Pair replacement may be reasonable when both units show similar deterioration.
No, unless the manufacturer explicitly specifies that application. Front and rear calipers usually differ in mounting, piston design, hose routing, and parking-brake provisions.
No. Current listings show both included and not-included hardware. Read the specifications and inspect the package contents before disassembly so missing reusable or replacement hardware can be addressed.
Driving is not recommended when braking is compromised. A leak, soft pedal, warning light, severe pull, or persistent drag can reduce control or stopping ability, so have the system inspected and repaired first.
Brake hose do not always need replacement with new caliper. Learn how to identify a collapsed hose, when the old hose is safe to reuse, and whether to replace one hose, both sides, or all four.
Choosing between a brake caliper with or without a bracket is critical. While a bare caliper saves upfront costs, a seized bracket causes uneven pad wear. Buying a pre-assembled A-Premium caliper with bracket saves time and ensures durability.
In this expert guide, we share a foolproof 3-step diagnostics method—including the vertical drip test and the pressurized tissue method—to help you isolate the leak accurately, choose premium replacements, and restore your vehicle’s stopping power safely.
The brake caliper is a critical component in a vehicle's braking system, yet many drivers overlook its importance. This blog explores the workings of the brake caliper, focusing on its role in generating the friction that slows and stops the vehicle.
Does your ford f150's inability to slow down or stop as first as it did when new bother you? Then the problem might be the brake calipers. All mechanical parts of a truck need regular maintenance to uphold their functions.
